1 pilot jet size 17.5
Can use of Jupiter-Z or Shogun SP. If you want to use a cheaper brand Kitaco or Extreme.
Can use of Jupiter-Z or Shogun SP. If you want to use a cheaper brand Kitaco or Extreme.
2 Remove the cylinder head gasket
Use 1 wrote that the middle layer. This step is meant to raise the compression ratio. If you want to raise even higher the compression, the lower block gasket can be removed and ga have to use a gasket. Simply use gasket glue wrote (the top tetep use 1 gasket). This trick dah tried and proven piston valve or not a collision with no oil leaks.
Use 1 wrote that the middle layer. This step is meant to raise the compression ratio. If you want to raise even higher the compression, the lower block gasket can be removed and ga have to use a gasket. Simply use gasket glue wrote (the top tetep use 1 gasket). This trick dah tried and proven piston valve or not a collision with no oil leaks.
3 Porting polish
Holes in and out of each at inflated diameter 1 mm.
Holes in and out of each at inflated diameter 1 mm.
4 Replace carburetor RX King
Mean step number 1 is not necessary. RX King had a disposable suggestions for cheap and suitable. Can directly plug into the intake manifold and air filter standard. Nozzle can try MJ 150 PJ 20 1.5 Setting air counter-clockwise rotation (note each motor can be different). The position of skepticism in threaded needle clip number 2 from above.
Mean step number 1 is not necessary. RX King had a disposable suggestions for cheap and suitable. Can directly plug into the intake manifold and air filter standard. Nozzle can try MJ 150 PJ 20 1.5 Setting air counter-clockwise rotation (note each motor can be different). The position of skepticism in threaded needle clip number 2 from above.
5. Teeth TOP 1 eye
This means that advance the timing to get in and exhaust valves. If you want more advance again the setting is the inclusion of advanced valve 1 eye then dump was scrubbed 1 eye. The technical term for narrowing its LSA (Lobe Separation Angle. Optimize Make rinsing process at high speed but the results are also steady estrangement valve should be made more narrow (so in 0.07 mm and 0.1 mm out) from standard sizes by means of thick mainin shim it.
This means that advance the timing to get in and exhaust valves. If you want more advance again the setting is the inclusion of advanced valve 1 eye then dump was scrubbed 1 eye. The technical term for narrowing its LSA (Lobe Separation Angle. Optimize Make rinsing process at high speed but the results are also steady estrangement valve should be made more narrow (so in 0.07 mm and 0.1 mm out) from standard sizes by means of thick mainin shim it.
6 Remove the air filter
If it replace the carburetor, which removed only the air filter element only, namely that there is no paper filter. While the crib is still attached and connected to the carburetor. If you still want to rely on the standard carburetor standard filter can still be used / installed but in some places the paper in the holes, 3 holes the size of 0.5 x 4 cm (length x height).
If it replace the carburetor, which removed only the air filter element only, namely that there is no paper filter. While the crib is still attached and connected to the carburetor. If you still want to rely on the standard carburetor standard filter can still be used / installed but in some places the paper in the holes, 3 holes the size of 0.5 x 4 cm (length x height).
7 Cut the cable coil 2 cm
Cable resistance is reduced by approximately 10%. Remember to install the cord again to be really strong, how is inserted and rotated to form a screw.
Cable resistance is reduced by approximately 10%. Remember to install the cord again to be really strong, how is inserted and rotated to form a screw.
8 Iridium Spark Plug
Suggestion use rather cheap brand Sindengen / SDG. The result is tolerable. If you want to still use standard plugs can also be. Set again the gap be 0.9 to 1 mm.
Suggestion use rather cheap brand Sindengen / SDG. The result is tolerable. If you want to still use standard plugs can also be. Set again the gap be 0.9 to 1 mm.
9 Oil SAE 10W40
Use special motors (any kind that important brand original) with SAE 10W40.
Use special motors (any kind that important brand original) with SAE 10W40.
Dicustom standard exhaust muffler or buy in the store.
11. Position axle on the adjusting tone chain attempted on the next possible position se
If you need to cut 2 eyes of the chain. The advantage, the distance behind the front axle so the shorter the bike more agile maneuvering. Other properties for reducing noises chains because chains compete with the swing arm.
12. prop Per clutch in less than 1 mm
Can wear pieces per ring per clutch or buy (usually 2mm thickness). Continues at the end of the clutch cable at the top of the crankcase, in the end used as frequently used in the brake drum to restore the clutch lever quickly. The result is a clutch so quickly jump directly behind it and the motor so the clutch is released. These two steps can also be replaced with racing clutch for pairs per 100 - 150rb. But watch out! Some users complained bike racing clutch per good 3 months, after the per so mushy and less kicking again. Per standard clutch his kayak CBU especially the more durable and with fouled. Violence will per equivalent per racing. But taking into account the side effects left hand fingers so stiff that through the traffic.
13. Pulser shifted 1-2 mm
Pulser is shifted to a more advanced spark plug sparks. Power will noticeably increase.
Pulser is shifted to a more advanced spark plug sparks. Power will noticeably increase.
14. front Gir
To use the 13 eye acceleration (default is 14 eyes) of Yamaha Crypton or F1ZR. Buy wrote that artificial Aspira or Indopart only 30 thousands. The result is more interesting bike again until 6th gear though. This step does not reduce significantly Top Speed. If in an urban or a traffic jam, instead just make the motor more quickly reach top speed. Top speed for changing the size of the front of the eyes of 15 eyes. Yamaha Jupiter can grab.
To use the 13 eye acceleration (default is 14 eyes) of Yamaha Crypton or F1ZR. Buy wrote that artificial Aspira or Indopart only 30 thousands. The result is more interesting bike again until 6th gear though. This step does not reduce significantly Top Speed. If in an urban or a traffic jam, instead just make the motor more quickly reach top speed. Top speed for changing the size of the front of the eyes of 15 eyes. Yamaha Jupiter can grab.
Next step is to replace the CDI, coil and a racing camshaft. For 3 of these items need 1.5 million. But very worth it when done. Suggestion Andrion use CDI XP HP 7 (400 thousand) combined with coil andrion well (170 thousand). For information, CDI BRT is actually good as well, it's just that according to its manufacturer and the results of the test, BRT is only suitable if the coil still use the standard. If the coil racing sometimes even drop his strength or CDI quickly die.
When racing CDI has replaced the valve spring should also be replaced tougher, can use the brand of racing like WRD, CLD, kindergarten, etc.. Or you can also use the original but fouled 1 mm (this is recommended because the case is the same as the per clutch, which is racing sometimes long gone soft. To camshaft / camshaft can use as WRD, CLD, Kawahara, Akutagawa.
Gear 13/43
