How to recondition the current Alfa nearly 23-year-old two-wheeled world enliven Indonesia?
1 Fix the double starter
According to the segment average wear womanhood, then the obligatory starter maximized. To make it easier to use. The key just in rotor spool, bushing, charcoal starter brush and double cable. Problem is most often the case, the rotor began stacked black crust, charcoal brush wear and cable-vong started jamming.
For problems charcoal brush wear and no cables to connect, can be treated with replacement. If the rotor coil spool adequately cleaned. Oh yes, also check the bushing as the rotor coil holder, sometimes also experience wear. If worn, must be taken to service the starter dynamo, where many of his bushing material contained therein.
2 Sil machine equipment
In Alfa starter pedal shaft seals there, gear shaft seals, shaft seals and magnetic seals the rear gear. Most fatal magnet seal, this seal because at Alfa served as a guarantor when the fresh gas density compression rinsed. It's on the left side, behind the rotor magnets. Easy to physical examination, because when it's worn around as crutches raised blackish kind of spark plugs wet gas dissipation. If it comes to things like that, as soon as possible replacement.
So is the pedal gearbox seals, spindle effect began to wear on the hinge points, gear pedal shaft rotation can no longer be spun at one point. But it tends to be twisted and scour occurs on the gear shaft seals.
If it comes to it, do not just replacement gear shaft seal alone, it is better to do a semi overhaul to dismantle Kalter right side (clutch) and perform the checks on the spindle, the successor movement to the drum shaft gear drive transmission gear shift. Next, if the rear gear shaft seals and shaft seals wear out the starter pedal, it's just the effect of too long enough replacement seals and seals which orsi.
3 Cylinder rear drum
The average score in this section, the brake booster has been added to the plate, the effect of the diameter of the cylindrical drum that is the greater. With intent, the brake is on stand-by condition ready to open or close the cylinder drum brake pedal in order to be more effective footing.
If transmissivity play chock, brake pad area of the cylinder drum so do not eat average, tend to be eroded in part be fouled. So be wise if the replacement drum. No need to wear orsi Alfa, can be cannibalized from Jupiter-Z. Therefore, the diameter of the cylinder is proportional to the Jupiter-Z. Certainly become more rear braking grip. And to use the bearing and the axle amputation gentlemen belonging to Jupiter-Z.
4. stretcher front tomorrow F1Z-R
It's hard when drum brakes are still adheres to the model, so dependence arises with the rear brake. When mixed in with the development of motor current, clear miss. The right choice when replacing front tomorrow belongs F1Z-R which is equipped with a caliper adapter mounting holes. Sipnya, equal to the diameter of the inner tube fastener holes in a triangle. Continue replacing the drum front-owned F1Z-R, complete with discs, calipers and master. Guaranteed to be more fashionable and safety.
5. Membrane replace carbon reinforced
When the deceleration, the roar of the engine can not clean, still arise subsequent combustion. Thus, in the use of gases lead, but actually not. This problem is common effects of leaf membrane begin Shining, or can not close tightly.
So to overcome this, could follow the style tuner that handles duck road race 2 stroke. Namely through the use of carbon reinforced membranes are resistant to high temperatures. So it is more accurate in controlling the supply of fresh gas into the hole rinse. This method can also indirectly save the fuel consumption.
6 Power engine wilder
If by chance a teenager riding, the engine power can be brought up again. Of standard spec stroke (50 mm) and the bore (52 mm), raised enough diameter cylinder. Quite cannibals piston Yamaha RX-S over size 100 (54 mm), a hefty capacity can be increased up to 114 engines, 45 cc.
The assumption, ported the cylinder liner must be setup again, according to the position of the piston when in TMA and TMB. In order to track the transfer and exhaust port hole unhindered piston position, when the fresh gas and exhaust gas circulation. If it is ported, then the replacement of its substitution maintain piston wear RX-S, so that power can be comparable with the motor younger.
7 head lamp frosted glass
Not the fault of the owner, because the spare head lamp orsi although difficult to track in official garage main dealer level 1 class. There is no other way except to raise the head lamp and tidy use of fiber, to replace the head lamp owned F1Z-R.
